|
Mobile Sanitizer: Cleaning and Sanitizing Ozone System
The Mobile Sanitizer is the perfect answer for mobile cleaning, disinfecting, and sanitization applications.
Since it is able to move throughout your processing plant, you can use the Mobile Sanitizer to move freely around your processing equipment and access hard to reach areas. The Mobile Sanitizer delivers a stream of high pressure water up to 100 psi, blasting away debris, grease, and other organics. At the same time, it outputs a concentrated ozone solution that cuts away bacteria and bio-films on your processing surfaces. Since it is a high pressure washer and sanitizer in one package, you eliminate the five step cleaning process by combining it into one simple solution. Also see our 2500 psi mobile sanitizer, The Pulsator.
Eliminates:
- Hot water cleaning
- Ceiling pipe condensation
- Chemicals - rinsing - odors
- Bio-film - E-Coli - Listeria
|
Reduces:
- Energy costs
- Water consumption
- Chemical waste and disposal costs
- Labor cost
- Most degreasers
|
Standard Features Include:
- Solid state, High frequency, Low voltage, Air-cooled, Stainless Steel, Corona discharge and Pyrex glass tube dielectric, for years of dependability.
- The patented OSF System produces microscopic bubbles, which are recycled for more contact time.
- Ozone gas is automatically metered in water by flow of water from 1 - 30 GPM.
- Fail-safe ozone controller sensor will shut down the ozone generator if the OSHA Safety level of .100PPm of ozone in air is exceeded.
- One Hp stainless steel booster pump for the ozone injector.
- Ozone resistant off-gas float valve for additional safety.
- Water back-flow prevention with double check valve.
- Power 120V - 60Hz 20A - UL Listed
As a manufacturer of ozone water purification systems, we take pride in offering high quality, state of the art, cost effective products.
Statistical Data
Test Plate Information and Results
Test Site: Processing Area for Pork and Beef
Name of Test: Hot Water/Conventional Chemical Versus High Power Ozone |
Bacteria per CM2 before test commences |
Bacteria per CM2
after the 5 steps*
1800 H2O, foam and chlorine
|
Bacteria per CM2
after using Ozone
with "The Pulsator" |
| 1. Transport Box |
TNTC |
19 |
2 |
| 2. Cutting Knife |
TNTC |
7 |
1 |
| 3. Band Saw 1 |
TNTC |
3 |
0 |
| 4. Band Saw 2 |
TNTC |
3 |
1 |
| 5. Rack for Transport Boxes |
TNTC |
4 |
0 |
| 6. Dumping Wagon |
TNTC |
17 |
0 |
| 7. Meat Conveyor |
TNTC |
20 |
0 |
| 8. Rack of Meat Conveyor 1 |
TNTC |
21 |
0 |
| 9. Carrying Bone Conveyor |
TNTC |
3 |
0 |
| 10. Cutting Table |
TNTC |
6 |
0 |
| 11. Cutter |
TNTC |
0 |
0 |
| 12. Handsaw - handle |
TNTC |
29 |
0 |
| 13. Handsaw - saw blade |
TNTC |
3 |
0 |
| 14. Rack of Meat Conveyor 2 |
TNTC |
25 |
0 |
| 15. Cutting Table |
TNTC |
8 |
0 |
| 16. Table |
TNTC |
22 |
0 |
| 17. Meat Conveyor |
TNTC |
10 |
0 |
*Under normal conditions there are 5 steps to clean-sanitize this beef area using 1800 H2O, foam and chlorine
1. Cleaning with 1800 hot water
2. Foam - to remove grease
3. Rinse foam/grease with hot water
4. Use chlorine disinfectant
5. Remove chlorine with hot water |
Time and water usage test / Loin Puller |
| |
Conventional
Gallons per minute - 15 |
Ozone with "The Pulsator"
Gallons per minute - 3.5 |
| Prerinse |
31 minutes |
~ |
| Foaming |
3 minutes |
~ |
| Dwell time |
10 minutes |
~ |
| Rinse |
3 minutes |
~ |
| Sanitation |
2 minutes |
~ |
| Total minutes |
49 minutes |
13 minutes |
| Gallons of water |
510 gallons |
46 gallons |
| Chemicals used |
WR Degreaser
E Chem Sanitizer |
None
Cold water/ No chemicals |
73% in manhour savings!
464 gallons of water saved! |
|
